开源鸿蒙 FAT

2022-08-09
浏览 (706)

FAT

Basic Concepts

File Allocation Table (FAT) is a file system developed for personal computers. It consists of the DOS Boot Record (DBR) region, FAT region, and Data region. Each entry in the FAT region records information about the corresponding cluster in the storage device. The cluster information includes whether the cluster is used, number of the next cluster of the file, whether the file ends with the cluster.

The FAT file system supports multiple formats, such as FAT12, FAT16, and FAT32. The numbers 12, 16, and 32 indicate the number of bits per cluster within the FAT, respectively. The FAT file system supports multiple media, especially removable media (such as USB flash drives, SD cards, and removable hard drives). The FAT file system ensures good compatibility between embedded devices and desktop systems (such as Windows and Linux) and facilitates file management.

The OpenHarmony kernel supports FAT12, FAT16, and FAT32 file systems. These file systems require a tiny amount of code to implement, use less resources, support a variety of physical media, and are tailorable and compatible with Windows and Linux systems. They also support identification of multiple devices and partitions. The kernel supports multiple partitions on hard drives and allows creation of the FAT file system on the primary partition and logical partition.

Development Guidelines

Driver Adaptation

The use of the FAT file system requires support from the underlying MultiMedia Card (MMC) drivers. To run FatFS on a board with an MMC storage device, you must:

Implement the disk_status, disk_initialize, disk_read, disk_write, and disk_ioctl APIs to adapt to the embedded MMC (eMMC) drivers on the board.
Add the fs_config.h file with information such as FS_MAX_SS (maximum sector size of the storage device) and FF_VOLUME_STRS (partition names) configured.

The following is an example:

#define FF_VOLUME_STRS     "system", "inner", "update", "user"
#define FS_MAX_SS          512
#define FAT_MAX_OPEN_FILES 50

How to Develop

NOTE

Note the following when managing FatFS files and directories: - A file cannot exceed 4 GB. - FAT_MAX_OPEN_FILES specifies the maximum number files you can open at a time, and FAT_MAX_OPEN_DIRS specifies the maximum number of folders you can open at a time. - Root directory management is not supported. File and directory names start with the partition name. For example, user/testfile indicates the file or directory testfile in the user partition. - To open a file multiple times, use O_RDONLY (read-only mode). O_RDWR or O_WRONLY (writable mode) can open a file only once. - The read and write pointers are not separated. If a file is open in O_APPEND mode, the read pointer is also at the end of the file. If you want to read the file from the beginning, you must manually set the position of the read pointer. - File and directory permission management is not supported. - The stat and fstat APIs do not support query of the modification time, creation time, and last access time. The Microsoft FAT protocol does not support time before A.D. 1980.

Note the following when mounting and unmounting FatFS partitions: - Partitions can be mounted with the read-only attribute. When the input parameter of the mount function is MS_RDONLY, all APIs with the write attribute, such as write, mkdir, unlink, and open with non-O_RDONLY attributes, will be rejected. - You can use the MS_REMOUNT flag with mount to modify the permission for a mounted partition. - Before unmounting a partition, ensure that all directories and files in the partition are closed. - You can use umount2 with the MNT_FORCE parameter to forcibly close all files and folders and unmount the partition. However, this may cause data loss. Therefore, exercise caution when running umount2.

The FAT file system supports re-partitioning and formatting of storage devices using fatfs_fdisk and fatfs_format. - If a partition is mounted before being formatted using fatfs_format, you must close all directories and files in the partition and unmount the partition first. - Before calling fatfs_fdisk, ensure that all partitions in the device are unmounted. - Using fatfs_fdisk and fatfs_format may cause data loss. Exercise caution when using them.

Development Example

Example Description

This example implements the following:

Create the user/test directory.
Create the file.txt file in the user/test directory.
Write Hello OpenHarmony! at the beginning of the file.
Save the file to a device.
Set the offset to the start position of the file.
Read the file.
Close the file.
Delete the file.
Delete the directory.

Sample Code

Prerequisites

The MMC device partition is mounted to the user directory.

The sample code is as follows:

  #include <stdio.h>
  #include <string.h>
  #include "sys/stat.h"
  #include "fcntl.h"
  #include "unistd.h"

  #define LOS_OK 0
  #define LOS_NOK -1

  int FatfsTest(void) 
  {     
    int ret;
    int fd = -1;
    ssize_t len;
    off_t off;
    char dirName[20] = "user/test";
    char fileName[20] = "user/test/file.txt";
    char writeBuf[20] = "Hello OpenHarmony!";
    char readBuf[20] = {0};

    /* Create the user/test directory. */
    ret = mkdir(dirName, 0777);
    if (ret != LOS_OK) {
        printf("mkdir failed.\n");
        return LOS_NOK;
    }

    /* Create a readable and writable file named file.txt in the user/test/ directory. */
    fd = open(fileName, O_RDWR | O_CREAT, 0777);
    if (fd < 0) {
        printf("open file failed.\n");
        return LOS_NOK;
    }

    /* Write the content from writeBuf to the file. */
    len = write(fd, writeBuf, strlen(writeBuf));
    if (len != strlen(writeBuf)) {
        printf("write file failed.\n");
        return LOS_NOK;
    }

    /* Save the file to a storage device. */
    ret = fsync(fd);
    if (ret != LOS_OK) {
        printf("fsync failed.\n");
        return LOS_NOK;
    }

    /* Move the read/write pointer to the beginning of the file. */
    off = lseek(fd, 0, SEEK_SET);
    if (off != 0) {
        printf("lseek failed.\n");
        return LOS_NOK;
    }

    /* Read the file content with the length of readBuf to readBuf. */
    len = read(fd, readBuf, sizeof(readBuf));
    if (len != strlen(writeBuf)) {
        printf("read file failed.\n");
        return LOS_NOK;
    }
    printf("%s\n", readBuf);

    /* Close the file. */
    ret = close(fd);
    if (ret != LOS_OK) {
        printf("close failed.\n");
        return LOS_NOK;
    }

    /* Delete the file file.txt from the user/test directory. */
    ret = unlink(fileName);
    if (ret != LOS_OK) {
        printf("unlink failed.\n");
        return LOS_NOK;
    }

    /* Delete the user/test directory. */
    ret = rmdir(dirName);
    if (ret != LOS_OK) {
        printf("rmdir failed.\n");
        return LOS_NOK;
    }

    return LOS_OK;
    }